Mindray DPM 1 Manuel de l'opérateur Page 95
- Page / 120
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
B-3
Guidance and Declaration - Electromagnetic Immunity
The device is suitable for use in the electromagnetic environment specified below. The customer
or the user of the device should assure that it is used in such an environment.
Immunity
tests
IEC 60601
Test level
Compliance
level
Electromagnetic environment —
——
— guidance
Conduced RF
IEC61000-4-6
3 Vrms
150k to 80MHz
3 Vrms
Radiated RF
IEC61000-4-3
3V/m
80M to 2.5GHz
3V/m
Portable and mobile RF communications
equipment should be used no closer to any
part of the device, including cables, than the
recommended separation distance calculated
from the equation applicable to the frequency
of the transmitter. Recommended separation
distance:
Pd 2.1=
Pd 2.1=
80M to 800MHz
Pd 3.2=
800M to 2.5GHz
where P is the maximum output power rating
of the transmitter in watts (W) according to
the transmitter manufacturer and d is the
recommended separation distance in meters
(m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site survey,
a
should be less than the compliance level in
each frequency range
b
Interference may
occur in the vicinity of equipment marked
with the following symbol:
.
Note 1: From 80 MHz to 800 MHz, the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, objects and people.
a: Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast
cannot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site
survey should be considered. If the measured field strength in the location in which the device is
used exceeds the applicable RF compliance level above, the device should be observed to verify
normal operation. If abnormal performance is observed, additional measures may be necessary,
such as reorienting or relocating the device.
b: Over the frequency ranges 150kHz to 80MHz, field strengths should be less than 3V/m.
- DPM 3 Vital Signs Monitor 1
- Operator’s Manual 1
- Revision History 3
- Warranty 5
- Exemptions 5
- Return Policy 6
- Contact Information 6
- Preface 7
- Contents 9
- 1 Safety 13
- 1.1.1 Warnings 14
- WARNING 14
- 1.1.2 Cautions 15
- CAUTION 15
- 1.2 Equipment Symbols 16
- 2 The Basics 19
- 2.1.3 Components 20
- 2.1.4 Functions 20
- 2.2 Appearance 21
- 2.2.2 Rear Panel 25
- 2.2.3 Recorder 26
- 2.3 Display 27
- 2.4 Battery 28
- 2.4.1 Battery Maintenance 29
- 2.4.2 Battery Recycling 30
- Installation and Maintenance 31
- 3.1.4 Bracket Mounting 32
- 3.1.5 Installation Method 33
- 3.2 Maintenance 37
- 3.2.1 Inspection 38
- 3.2.2 Cleaning 38
- 3.2.3 Disinfection 40
- 4 Menus and Screens 41
- 4.2 System Setup 42
- 4.2.2 Network Setup 43
- 4.2.3 Time Setup 44
- 4.2.4 User Maintenance 44
- 4.2.5 Nurse Call Setup 45
- WARNING 46
- 4.2.6 Version 46
- 4.2.7 Configuration 46
- 4.3 Normal Screen 47
- 4.4 Trend Screen 48
- 4.5 Standby State 49
- 5 Alarms 51
- 5.2 Alarm Indications 52
- 5.2.1 Alarm Lamp 53
- 5.2.2 Audible Alarms 53
- 5.2.3 Alarm Messages 53
- 5.3 Alarm Status 54
- 5.3.3 Alarms Paused 55
- 5.3.4 Alarm Silenced 56
- 5.3.5 Status Switchover 56
- 5.5 Setting Alarms 57
- Sensor Off Alarm 58
- 5.7 When an Alarm Occurs 58
- 6 Recording 59
- 6.3 Loading Paper 60
- 6.4 Removing Paper Jam 61
- Monitoring 63
- 7.2 Safety 64
- 7.3 Monitoring Procedure 65
- 7.4 Measurement Limitations 65
- 7.5 Masimo Information 66
- 7.6 Nellcor Information 66
- 8 NIBP Monitoring 67
- 8.2 Monitoring Procedure 68
- 8.2.2 Operation Guides 69
- 8.3 Measurement Limitations 70
- 8.4.2 Resetting NIBP 71
- 8.4.3 Calibrating NIBP 72
- 8.4.4 NIBP Leakage Test 73
- 9 TEMP Monitoring 75
- 9.2 Temperature Setup 76
- 9.3 Monitoring Procedure 76
- ™ TEMP Probe 79
- 9.5 Precautions 80
- 10 Accessories 81
- 10.2 NIBP Accessories 83
- 10.3 TEMP Accessories 84
- 10.4 Others 84
- A Product Specifications 85
- A.3 Power Requirements 86
- A.4 Hardware Specification 87
- A.5 Signal Output 88
- Specification 88
- A.6.2 Masimo SpO 89
- A.7 NIBP Specification 90
- A.8 TEMP Specification 91
- C.2 Technical Alarm Messages 97
- C.2.3 Mindray DS SpO 100
- Module Alarm Messages 100
- C.2.4 Masimo SpO 101
- C.2.5 Nellcor SpO 103
- C.3 Prompt Messages 108
- FOR YOUR NOTES 110
- D Factory Defaults 111
- D.2 System Setup 112
- D.3 Alarm Limit 113
- E Symbols and Abbreviation 115
- E.2 Symbols 116
- E.3 Abbreviations 117
Produits connexes et manuels pour Mesure, test et contrôle Mindray DPM 1
(274 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels