Mindray DPM 1 Manuel de l'opérateur Page 75
- Page / 120
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9-1
9 TEMP Monitoring
9.1 Overview
The SmarTemp™ TEMP module is intended for monitoring oral, axillary and rectal
temperature of adult and pediatric patients and axillary temperature of neonatal patients. Be
sure to set correct monitoring mode and position and to select appropriate temperature
probe before taking measurement. TEMP TYPE can be set to PREDICT or MONITOR. The
default TEMP TYPE is PREDICT.
PREDICT MODE: In PREDICT mode, the TEMP probe warms up automatically as
the probe is withdrawn from the probe sheath. Warming up takes approximately 10s at
25℃ and when it is done, the monitor gives two beeps. Final temperature is obtained
in approximately 10s to12s and the monitor gives a beep. Temperature reading remains
on the display till the probe is removed from the sheath again. In this mode, if no
accurate patient temperature is reached, or after the probe is removed from the sheath
for 60s, neither measurement is taken nor the probe is not replaced in its sheath, the
monitor automatically enters the MONITOR mode.
MONITOR MODE: In MONITOR mode, final temperature is reached in 3 to 5
minutes and the temperature reading is continuously shown. In this mode, the monitor
does not beep when the final temperature is obtained.
The TEMP reading is display above the LCD.
WARNING
The TEMP module shall only be operated under specified environment. When
the probe is removed from the probe sheath, the monitor detects the ambient
temperature. An auditory alarm will be triggered and the alarm message “
““
“ENV
TEMP OVERRANGE”
””
”will be displayed if the ambient temperature is over
range.
For neonatal patient, only axillary temperature can be taken.
Choose appropriate probe according to temperature position. Incorrect probe
may result in erroneous measurement.
Prolonged and continuous monitoring beyond 5 minutes is not recommended in
any mode.
In PREDICT mode, temperature probe shall be placed to the measured site as
soon as probe warmup is completed; otherwise, inaccurate temperature reading
may result.
In MONITOR mode, the monitor stops measurement after performing
measurement for five minutes later and the TEMP reading disappears.
Long-time TEMP measurement may cause patient discomfort.
- DPM 3 Vital Signs Monitor 1
- Operator’s Manual 1
- Revision History 3
- Warranty 5
- Exemptions 5
- Return Policy 6
- Contact Information 6
- Preface 7
- Contents 9
- 1 Safety 13
- 1.1.1 Warnings 14
- WARNING 14
- 1.1.2 Cautions 15
- CAUTION 15
- 1.2 Equipment Symbols 16
- 2 The Basics 19
- 2.1.3 Components 20
- 2.1.4 Functions 20
- 2.2 Appearance 21
- 2.2.2 Rear Panel 25
- 2.2.3 Recorder 26
- 2.3 Display 27
- 2.4 Battery 28
- 2.4.1 Battery Maintenance 29
- 2.4.2 Battery Recycling 30
- Installation and Maintenance 31
- 3.1.4 Bracket Mounting 32
- 3.1.5 Installation Method 33
- 3.2 Maintenance 37
- 3.2.1 Inspection 38
- 3.2.2 Cleaning 38
- 3.2.3 Disinfection 40
- 4 Menus and Screens 41
- 4.2 System Setup 42
- 4.2.2 Network Setup 43
- 4.2.3 Time Setup 44
- 4.2.4 User Maintenance 44
- 4.2.5 Nurse Call Setup 45
- WARNING 46
- 4.2.6 Version 46
- 4.2.7 Configuration 46
- 4.3 Normal Screen 47
- 4.4 Trend Screen 48
- 4.5 Standby State 49
- 5 Alarms 51
- 5.2 Alarm Indications 52
- 5.2.1 Alarm Lamp 53
- 5.2.2 Audible Alarms 53
- 5.2.3 Alarm Messages 53
- 5.3 Alarm Status 54
- 5.3.3 Alarms Paused 55
- 5.3.4 Alarm Silenced 56
- 5.3.5 Status Switchover 56
- 5.5 Setting Alarms 57
- Sensor Off Alarm 58
- 5.7 When an Alarm Occurs 58
- 6 Recording 59
- 6.3 Loading Paper 60
- 6.4 Removing Paper Jam 61
- Monitoring 63
- 7.2 Safety 64
- 7.3 Monitoring Procedure 65
- 7.4 Measurement Limitations 65
- 7.5 Masimo Information 66
- 7.6 Nellcor Information 66
- 8 NIBP Monitoring 67
- 8.2 Monitoring Procedure 68
- 8.2.2 Operation Guides 69
- 8.3 Measurement Limitations 70
- 8.4.2 Resetting NIBP 71
- 8.4.3 Calibrating NIBP 72
- 8.4.4 NIBP Leakage Test 73
- 9 TEMP Monitoring 75
- 9.2 Temperature Setup 76
- 9.3 Monitoring Procedure 76
- ™ TEMP Probe 79
- 9.5 Precautions 80
- 10 Accessories 81
- 10.2 NIBP Accessories 83
- 10.3 TEMP Accessories 84
- 10.4 Others 84
- A Product Specifications 85
- A.3 Power Requirements 86
- A.4 Hardware Specification 87
- A.5 Signal Output 88
- Specification 88
- A.6.2 Masimo SpO 89
- A.7 NIBP Specification 90
- A.8 TEMP Specification 91
- C.2 Technical Alarm Messages 97
- C.2.3 Mindray DS SpO 100
- Module Alarm Messages 100
- C.2.4 Masimo SpO 101
- C.2.5 Nellcor SpO 103
- C.3 Prompt Messages 108
- FOR YOUR NOTES 110
- D Factory Defaults 111
- D.2 System Setup 112
- D.3 Alarm Limit 113
- E Symbols and Abbreviation 115
- E.2 Symbols 116
- E.3 Abbreviations 117
Produits connexes et manuels pour Mesure, test et contrôle Mindray DPM 1
(274 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels