Mindray DPM 1 Manuel de l'opérateur Page 64
- Page / 120
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7-2
7.2 Safety
WARNING
Use only SpO
2
sensors specified in this manual. Follow the SpO
2
sensor’s
instructions for use and adhere to all warnings and cautions.
When a trend toward patient deoxygenation is indicated, blood samples should be
analyzed by a co-oximeter to completely understand the patient’s condition.
Do not use SpO
2
sensors during magnetic resonance imaging (MRI). Induced
current could potentially cause burns. The sensor may affect the MRI image, and
the MRI unit may affect the accuracy of the oximetry measurements.
Prolonged continuous monitoring may increase the risk of undesirable changes in
skin characteristics, such as irritation, reddening, blistering or burns. Inspect the
sensor site every two hours and move the sensor if the skin quality changes. For
neonates, or patients with poor peripheral blood circulation or sensitive skin,
inspect the sensor site more frequently.
Check if the sensor is in normal condition before monitoring. Do not use the SpO
2
sensor once the package or the sensor is found damaged.
After unplugging the SpO
2
sensor cable from the connector of the monitor, the
system shall display the alarm message "SPO2 SENSOR OFF" and give the
audible alarm.
ES (Electrosurgery) equipment wire and SpO
2
cable must not be tangled up.
Do not apply the sensor on a limb with an intravenous infusion or arterial catheter
in place.
Do not perform SpO
2
monitoring and NIBP measurements on the same limb
simultaneously. Obstruction of blood flow during NIBP measurements may
adversely affect the SpO
2
reading.
Measure the monitor’s leakage current whenever an external device is connected to
the serial port. Leakage current must not exceed 100 mA.
To ensure patient electrical isolation, connect only to other equipment with
electronically isolated circuits.
Do not connect the monitor to a mains outlet with a wall switch or dimmer.
Interfering Substances, such as carboxyhemoglobin, may erroneously increase
SpO
2
readings. The level of increase is approximately equal to the amount of
carboxyhemoglobin. Dyes, or any substance containing dyes, that change usual
arterial pigmentation may also cause the increase of SpO
2
readings.
- DPM 3 Vital Signs Monitor 1
- Operator’s Manual 1
- Revision History 3
- Warranty 5
- Exemptions 5
- Return Policy 6
- Contact Information 6
- Preface 7
- Contents 9
- 1 Safety 13
- 1.1.1 Warnings 14
- WARNING 14
- 1.1.2 Cautions 15
- CAUTION 15
- 1.2 Equipment Symbols 16
- 2 The Basics 19
- 2.1.3 Components 20
- 2.1.4 Functions 20
- 2.2 Appearance 21
- 2.2.2 Rear Panel 25
- 2.2.3 Recorder 26
- 2.3 Display 27
- 2.4 Battery 28
- 2.4.1 Battery Maintenance 29
- 2.4.2 Battery Recycling 30
- Installation and Maintenance 31
- 3.1.4 Bracket Mounting 32
- 3.1.5 Installation Method 33
- 3.2 Maintenance 37
- 3.2.1 Inspection 38
- 3.2.2 Cleaning 38
- 3.2.3 Disinfection 40
- 4 Menus and Screens 41
- 4.2 System Setup 42
- 4.2.2 Network Setup 43
- 4.2.3 Time Setup 44
- 4.2.4 User Maintenance 44
- 4.2.5 Nurse Call Setup 45
- WARNING 46
- 4.2.6 Version 46
- 4.2.7 Configuration 46
- 4.3 Normal Screen 47
- 4.4 Trend Screen 48
- 4.5 Standby State 49
- 5 Alarms 51
- 5.2 Alarm Indications 52
- 5.2.1 Alarm Lamp 53
- 5.2.2 Audible Alarms 53
- 5.2.3 Alarm Messages 53
- 5.3 Alarm Status 54
- 5.3.3 Alarms Paused 55
- 5.3.4 Alarm Silenced 56
- 5.3.5 Status Switchover 56
- 5.5 Setting Alarms 57
- Sensor Off Alarm 58
- 5.7 When an Alarm Occurs 58
- 6 Recording 59
- 6.3 Loading Paper 60
- 6.4 Removing Paper Jam 61
- Monitoring 63
- 7.2 Safety 64
- 7.3 Monitoring Procedure 65
- 7.4 Measurement Limitations 65
- 7.5 Masimo Information 66
- 7.6 Nellcor Information 66
- 8 NIBP Monitoring 67
- 8.2 Monitoring Procedure 68
- 8.2.2 Operation Guides 69
- 8.3 Measurement Limitations 70
- 8.4.2 Resetting NIBP 71
- 8.4.3 Calibrating NIBP 72
- 8.4.4 NIBP Leakage Test 73
- 9 TEMP Monitoring 75
- 9.2 Temperature Setup 76
- 9.3 Monitoring Procedure 76
- ™ TEMP Probe 79
- 9.5 Precautions 80
- 10 Accessories 81
- 10.2 NIBP Accessories 83
- 10.3 TEMP Accessories 84
- 10.4 Others 84
- A Product Specifications 85
- A.3 Power Requirements 86
- A.4 Hardware Specification 87
- A.5 Signal Output 88
- Specification 88
- A.6.2 Masimo SpO 89
- A.7 NIBP Specification 90
- A.8 TEMP Specification 91
- C.2 Technical Alarm Messages 97
- C.2.3 Mindray DS SpO 100
- Module Alarm Messages 100
- C.2.4 Masimo SpO 101
- C.2.5 Nellcor SpO 103
- C.3 Prompt Messages 108
- FOR YOUR NOTES 110
- D Factory Defaults 111
- D.2 System Setup 112
- D.3 Alarm Limit 113
- E Symbols and Abbreviation 115
- E.2 Symbols 116
- E.3 Abbreviations 117
Produits connexes et manuels pour Mesure, test et contrôle Mindray DPM 1
(274 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels