Mindray DPM 1 Manuel de l'opérateur télécharger pdf (Page 34)

3-4

3.1.5.2 Installing the battery

The battery compartment is located at the bottom of the patient monitor. Follow the steps

given below to install the battery.

1. Push the compartment door in the marked direction to open the door.

2. Flip the battery stopper to the left, as Figure 3-1 shows.

3. Follow the marked polarity to insert the battery into the compartment, as Figure 3-2

shows.

4. Push the battery to the bottom and flip the stopper back to the original position, as

Figure 3-3 shows.

5. Close the battery door.

Figure 3-1

Figure 3-2

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 119 120

DPM 3 Vital Signs Monitor 1
Operator’s Manual 1
Revision History 3
Warranty 5
Exemptions 5
Return Policy 6
Contact Information 6
Preface 7
Contents 9
1 Safety 13
1.1.1 Warnings 14
WARNING 14
1.1.2 Cautions 15
CAUTION 15
1.2 Equipment Symbols 16
2 The Basics 19
2.1.3 Components 20
2.1.4 Functions 20
2.2 Appearance 21
2.2.2 Rear Panel 25
2.2.3 Recorder 26
2.3 Display 27
2.4 Battery 28
2.4.1 Battery Maintenance 29
2.4.2 Battery Recycling 30
Installation and Maintenance 31
3.1.4 Bracket Mounting 32
3.1.5 Installation Method 33
3.2 Maintenance 37
3.2.1 Inspection 38
3.2.2 Cleaning 38
3.2.3 Disinfection 40
4 Menus and Screens 41
4.2 System Setup 42
4.2.2 Network Setup 43
4.2.3 Time Setup 44
4.2.4 User Maintenance 44
4.2.5 Nurse Call Setup 45
WARNING 46
4.2.6 Version 46
4.2.7 Configuration 46
4.3 Normal Screen 47
4.4 Trend Screen 48
4.5 Standby State 49
5 Alarms 51
5.2 Alarm Indications 52
5.2.1 Alarm Lamp 53
5.2.2 Audible Alarms 53
5.2.3 Alarm Messages 53
5.3 Alarm Status 54
5.3.3 Alarms Paused 55
5.3.4 Alarm Silenced 56
5.3.5 Status Switchover 56
5.5 Setting Alarms 57
Sensor Off Alarm 58
5.7 When an Alarm Occurs 58
6 Recording 59
6.3 Loading Paper 60
6.4 Removing Paper Jam 61
Monitoring 63
7.2 Safety 64
7.3 Monitoring Procedure 65
7.4 Measurement Limitations 65
7.5 Masimo Information 66
7.6 Nellcor Information 66
8 NIBP Monitoring 67
8.2 Monitoring Procedure 68
8.2.2 Operation Guides 69
8.3 Measurement Limitations 70
8.4.2 Resetting NIBP 71
8.4.3 Calibrating NIBP 72
8.4.4 NIBP Leakage Test 73
9 TEMP Monitoring 75
9.2 Temperature Setup 76
9.3 Monitoring Procedure 76
™ TEMP Probe 79
9.5 Precautions 80
10 Accessories 81
10.2 NIBP Accessories 83
10.3 TEMP Accessories 84
10.4 Others 84
A Product Specifications 85
A.3 Power Requirements 86
A.4 Hardware Specification 87
A.5 Signal Output 88
Specification 88
A.6.2 Masimo SpO 89
A.7 NIBP Specification 90
A.8 TEMP Specification 91
C.2 Technical Alarm Messages 97
C.2.3 Mindray DS SpO 100
Module Alarm Messages 100
C.2.4 Masimo SpO 101
C.2.5 Nellcor SpO 103
C.3 Prompt Messages 108
FOR YOUR NOTES 110
D Factory Defaults 111
D.2 System Setup 112
D.3 Alarm Limit 113
E Symbols and Abbreviation 115
E.2 Symbols 116
E.3 Abbreviations 117

Commentaires sur ces manuels

Pas de commentaire

Mindray DPM 1 Manuel de l'opérateur Page 34

Commentaires sur ces manuels

Produits connexes et manuels pour Mesure, test et contrôle Mindray DPM 1