Mindray DPM 1 Manuel de l'opérateur Page 57
- Page / 120
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-7
5.4 Clearing Alarm Indications
1. Clearing alarm light flashing and alarm tones
For some technical alarms, the alarm lamp flashing and alarm tones are cleared and the
alarm messages change to prompt messages during and after the alarm paused period if
is pressed for less than 2 seconds. If the technical alarm is triggered again after the
monitor restores to the normal status, the monitor will give alarm indications as normal. For
technical alarms whose alarm light flashing and alarm tones can be cleared, refer to C
Alarm Messages and Prompt Information.
2. Clearing all alarm indications
For some other technical alarms, all alarm indications are cleared during and after the alarm
paused period if
is pressed for less than 2 seconds. If the technical alarm is
triggered again after the monitor restores to the normal status, the monitor will give alarm
indications as normal.
5.5 Setting Alarms
By pressing , you can enter the SET ALARMS menu to set NIBP and SpO2 alarm
switches and change alarm limits.
You can switch on or off NIBP-related physiological alarms by selecting the pane to the
right of SYS ALM and toggling between ON and OFF. You can switch on or off
physiological alarms related to SpO
2
and PR by selecting the pane to the right of SPO2
ALM and toggling between ON and OFF.
To adjust alarm limits, move the cursor respectively to HI and LO and select a desired value
by pressing
, and .
When any of the pressure values exceeds the alarm limits, an alarm will be triggered. The
ranges of NIBP limits is listed below:
Patient type Adult Pediatric Neonate
Sys 40 to 270 mmHg 40 to 200 mmHg 40 to 135 mmHg
Map 20 to 230 mmHg 20 to 165 mmHg 20 to 110 mmHg
Dia 10 to 210 mmHg 10 to 150 mmHg 10 to 100 mmHg
- DPM 3 Vital Signs Monitor 1
- Operator’s Manual 1
- Revision History 3
- Warranty 5
- Exemptions 5
- Return Policy 6
- Contact Information 6
- Preface 7
- Contents 9
- 1 Safety 13
- 1.1.1 Warnings 14
- WARNING 14
- 1.1.2 Cautions 15
- CAUTION 15
- 1.2 Equipment Symbols 16
- 2 The Basics 19
- 2.1.3 Components 20
- 2.1.4 Functions 20
- 2.2 Appearance 21
- 2.2.2 Rear Panel 25
- 2.2.3 Recorder 26
- 2.3 Display 27
- 2.4 Battery 28
- 2.4.1 Battery Maintenance 29
- 2.4.2 Battery Recycling 30
- Installation and Maintenance 31
- 3.1.4 Bracket Mounting 32
- 3.1.5 Installation Method 33
- 3.2 Maintenance 37
- 3.2.1 Inspection 38
- 3.2.2 Cleaning 38
- 3.2.3 Disinfection 40
- 4 Menus and Screens 41
- 4.2 System Setup 42
- 4.2.2 Network Setup 43
- 4.2.3 Time Setup 44
- 4.2.4 User Maintenance 44
- 4.2.5 Nurse Call Setup 45
- WARNING 46
- 4.2.6 Version 46
- 4.2.7 Configuration 46
- 4.3 Normal Screen 47
- 4.4 Trend Screen 48
- 4.5 Standby State 49
- 5 Alarms 51
- 5.2 Alarm Indications 52
- 5.2.1 Alarm Lamp 53
- 5.2.2 Audible Alarms 53
- 5.2.3 Alarm Messages 53
- 5.3 Alarm Status 54
- 5.3.3 Alarms Paused 55
- 5.3.4 Alarm Silenced 56
- 5.3.5 Status Switchover 56
- 5.5 Setting Alarms 57
- Sensor Off Alarm 58
- 5.7 When an Alarm Occurs 58
- 6 Recording 59
- 6.3 Loading Paper 60
- 6.4 Removing Paper Jam 61
- Monitoring 63
- 7.2 Safety 64
- 7.3 Monitoring Procedure 65
- 7.4 Measurement Limitations 65
- 7.5 Masimo Information 66
- 7.6 Nellcor Information 66
- 8 NIBP Monitoring 67
- 8.2 Monitoring Procedure 68
- 8.2.2 Operation Guides 69
- 8.3 Measurement Limitations 70
- 8.4.2 Resetting NIBP 71
- 8.4.3 Calibrating NIBP 72
- 8.4.4 NIBP Leakage Test 73
- 9 TEMP Monitoring 75
- 9.2 Temperature Setup 76
- 9.3 Monitoring Procedure 76
- ™ TEMP Probe 79
- 9.5 Precautions 80
- 10 Accessories 81
- 10.2 NIBP Accessories 83
- 10.3 TEMP Accessories 84
- 10.4 Others 84
- A Product Specifications 85
- A.3 Power Requirements 86
- A.4 Hardware Specification 87
- A.5 Signal Output 88
- Specification 88
- A.6.2 Masimo SpO 89
- A.7 NIBP Specification 90
- A.8 TEMP Specification 91
- C.2 Technical Alarm Messages 97
- C.2.3 Mindray DS SpO 100
- Module Alarm Messages 100
- C.2.4 Masimo SpO 101
- C.2.5 Nellcor SpO 103
- C.3 Prompt Messages 108
- FOR YOUR NOTES 110
- D Factory Defaults 111
- D.2 System Setup 112
- D.3 Alarm Limit 113
- E Symbols and Abbreviation 115
- E.2 Symbols 116
- E.3 Abbreviations 117
Produits connexes et manuels pour Mesure, test et contrôle Mindray DPM 1
(274 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels