Mindray TRIO Instructions d'exploitation Page 94
- Page / 170
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Trio™ Operating Instructions 0070-10-0666-01 2 - 65
Operations Alarms
COMMON ALARM SETUP Menu Selections
FIGURE 2-47 Common Alarm Setup Menu
ALM SEL
(Alarm Selection)
Choose COMMON ALARM SETUP.
ALARM VOL Volume of the audio alert. Selections are: LOW, MED, and HIGH.
ALM PRINT TIME Length of the printed waveform. Selections are: 8s, 16s, or 32s.
ALM MUTE TIME Length of time for the alarm to be silenced. Selections are:1min,
2min, 5min, 10min, and PERMANENT.
When ALM MUTE TIME is set to PERMANENT and Alarm Mute
is active, the message “Alarms Permanently Muted” displays at a
constant rate in the technical alarms area.
• If another technical alarm occurs at the same time, both
messages will display alternately.
•If the ALM MUTE TIME is changed to something other than
PERMANENT, the following conditions will exist:
• The elapsed time is defined as the time from which ALM
MUTE TIME had been set to PERMANENT to the time at
which it was changed to something other than
PERMANENT.
• If the elapsed time exceeds the newly selected ALM MUTE
TIME, then the Alarm Mute will immediately deactivate.
Example: Elapsed time = 5min, New ALM MUTE TIME =
2min, Alarm Mute immediately deactivates.
• If the elapsed time is less than the newly selected ALM
MUTE TIME, then the Alarm Mute will continue to be active
for the remainder of the newly selected time period.
Example: Elapsed time = 2min, New ALM MUTE TIME =
10min, Alarm Mute continues to be active for 8 minutes and
then deactivates.
- Operating Instructions 1
- Foreword 8
- Warnings 9
- Precautions 10
- Indication For Use 14
- Unpacking 14
- Introduction Symbols 15
- General Product Description 16
- Key Features 17
- 1.1 Front Panel 18
- 1.1.1 Front Panel Keypad 19
- 1.1.2 Display 21
- 1.2 Left Side Panel 25
- 1.3 Right Side Panel 26
- 1.4 Rear Panel 27
- Operations 30
- 2.2 Menus 31
- 2.3 System Menu 32
- 2.3.2 List Trend 34
- 2.3.3 Graphic Trend 34
- 2.3.4 Mark Event 35
- 2.3.5 Monitor Setup 35
- 2.3.5.1 Alarm Setup 36
- 2.3.5.2 Time Setup 36
- 2.3.5.3 Printer Setup 37
- 2.3.5.4 Analog Setup 39
- 2.3.5.5 Module Setup 39
- 2.3.5.6 Trace Setup 40
- 2.3.5.7 Parameter Colors 41
- 2.3.5.8 Restore Defaults 41
- 2.3.5.9 Save Current 42
- 2.3.6 Maintenance 42
- 2.3.7 Normal Screen 42
- 2.4 Parameter Menus 43
- 2.4.1.3 Lead Placement 45
- Standard 3-wire Lead Sets 45
- Standard 5-wire Lead Sets 46
- Parameter Menus Operations 47
- Lead II Monitoring 48
- 2.4.1.4 ECG Monitoring 51
- 2.4.1.6 ECG Setup 53
- Accessing the ECG Setup Menu 53
- ECG Setup Menu Selections 54
- Heart Rate Alarm Limits 56
- 2.4.1.7 ECG Troubleshooting 56
- 2.4.2 Respiration Monitoring 58
- Respiration Rate Alarm Limits 59
- 2.4.3 SpO 61
- Monitoring 61
- Performance Considerations 62
- Calibration 62
- Auto Scaling 62
- 2.4.3.1 Masimo SET 64
- Operations Parameter Menus 66
- 2.4.3.2 Nellcor 68
- Nellcor SpO 71
- Alarm Limits 71
- 2.4.3.2.2 Nellcor SpO 71
- Troubleshooting 71
- 2.4.4 NIBP Monitoring 73
- 2.4.4.1 Cuff Application 74
- 2.4.4.2 Measurement 75
- 2.4.4.3 NIBP Display Tile 76
- 2.4.4.4 NIBP Setup Menu 77
- Accessing the NIBP Setup Menu 77
- NIBP Setup Menu Selections 77
- Other Factors 80
- Newborn NIBP Technique 80
- 2.4.4.5 NIBP Troubleshooting 81
- 2.4.5 Temperature Monitoring 82
- 2.4.5.1 Temperature Setup 82
- Temperature Alarm Limits 83
- 2.4.6.1 IBP Select Menu 86
- Accessing the IBP Select Menu 86
- 2.4.6.2 IBP Setup Menu 87
- Accessing the IBP Setup Menu 87
- IBP Setup Menu Selections 88
- IBP Alarm Limits 90
- 2.4.6.3 IBP Troubleshooting 91
- 2.5 Alarms 92
- General Alarms 93
- 2.5.2 Alarm Priorities 93
- 2.5.3 Alarm Setup Menus 93
- Operations Alarms 100
- Alarms Operations 101
- Alarm Mute 104
- When an Alarm Occurs 104
- 2.5.4 Alarm Troubleshooting 104
- 2.6 Trends 105
- Graphic Trend Menu Selections 106
- Mark Event 107
- Remove Graphic Trend Display 107
- Delete Graphic Trend Data 107
- 2.6.2 List Trend 108
- List Trend Menu Selections 109
- Remove List Trend Display 109
- Delete List Trend Data 110
- 2.7 Recorder (Optional) 111
- Printer Setup Menu Selections 112
- Real-Time Print 112
- Interval Real-Time Printout 113
- Alarm Printout 113
- Graphic/List Trend Print 114
- Error Log Print 114
- Clear Print Tasks 115
- Defaults 116
- (Patient size) 117
- 3.1.3 Current Configuration 121
- User Maintenance 124
- 4.4.1 SpO 126
- Sensors 126
- 4.4.2 Blood Pressure Cuffs 127
- Antimicrobial Coating 128
- (Reusable) 129
- 4.7 Recorder Maintenance 130
- Accessories 134
- Appendix 140
- 6.1.2 Safety Designations 141
- 6.1.3 Performance / Accuracy 142
- 6.1.4 Environmental / EMC 143
- 6.2.1 ECG 144
- ≤ 300 μA RMS max 148
- *Adult and Pediatric 149
- 6.2.6.4 Heart Rate from NIBP 149
- ≥ 300 mmHg ≥ 243 mmHg 150
- NIBP Measurement Cycle 151
- 6.2.8 IBP Safety Requirements 151
- Masimo SET 154
- Reference Footnotes 154
- 6.3 Physical Specifications 156
- Electromagnetic Compatibility 162
- TABLE 6-2 163
- TABLE 6-3 164
- 6.4 Warranty Statements 167
- 0002-08-8918 170
Produits connexes et manuels pour Mesure, test et contrôle Mindray TRIO
(120 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels